Please approve Wires Crossed mock

Looks good to me. Approved!

- flamadiddle commented 124 days ago

Approved.

- Brandon commented 124 days ago

Approved (:

- Mijoja commented 124 days ago

APPROVED :D

- jcarff commented 124 days ago

I don't see any problems, but once again, why is the mock so unbelievably small?

- pakrem commented 124 days ago

I don't understand what the blue is for, but it looks good, so no complaints here. Approved.

- koikuri commented 124 days ago

I like it. But I agree that it's just a wee bit on the small side. Personally, about a 20-25%increase would be nice, but really isn't an issue. This is an awesome design. I don't know how I procrastinated enough to miss this. I'll be getting it at full price now.

@koikuri, I think the blue part is going to be the "tag" print on the inside back.

- dicom commented 124 days ago

Would it make sense to invert the image that's printed on the back? If you look at the bottom corners of the robot, and picture the two images front to back, they would not align unless the back image is inverted.

Otherwise, I see no problems with it, and I have no objection to it printing as is.

- Nailbunny commented 124 days ago

@Nailbunny,

Are you saying to flip the back print on it's vertical axis? If so, I can see what you're talking about more in the wheel than anything else.

- dicom commented 124 days ago

Approved, but quick question: On the dynamite, is the outline supposed to be that thin? Could that be a layering error or something? I also agree with dicom - a small size increase would be better, but it's not a big issue.

- monika commented 124 days ago

approved, looks good :)

- xenodus commented 124 days ago

I approve. It would not hurt the shirt if the image was larger, but I'm fine with it at the current size.

- Marco_Esquandolas commented 124 days ago

I think the size looks good as-is, but I wouldn't would mind if it were bigger.
I agree that the back image should be flipped to make it match up.
Can't wait to see it! :)

- lees300 commented 124 days ago

Approved. Love the size as is.

- raccoon27g commented 124 days ago

Approved as is however, the vertical shift mentioned above would make it line up better, honestly most people probably aren't going to notice.

- sweetooth commented 123 days ago

Approved! I'm looking forward to this one.

- needsnewbrain commented 123 days ago

approved

- so_in2arch commented 123 days ago

Love it, can't wait to wear it. Like how the robot is the same size but front and back. A little confused of where the blue is used on the design.

Approved

- Chit commented 123 days ago

approved!

- Adoni commented 122 days ago

We have increased the size of this design and inverted the back image. We will begin printing this.

- kamil commented 121 days ago

Very nice. I'm loving the size increase.

Also, on a side note, I hope it's ok to do something like this, but I made up a little deally to put in a sig or website to help promote stuff here. I currently have it up on my site, so if it's not permitted, I can remove it. Here's an example of it for this shirt.

- dicom commented 121 days ago

approved

- Adoni commented 116 days ago

approved

- Adoni commented 116 days ago

So has this gone to print, then? Any chance of it arriving before Christmas?

- AGrant311 commented 105 days ago

asked our printer and will get back to you with more info!!!!

- kamil commented 105 days ago

wires crossed has been printed and they should be ready for shipping to you soon....so x-mas is promising to receive this tee.

- kamil commented 105 days ago

I received the tee today!!! It looks great!!!

- pakrem commented 93 days ago